SENSOR ACCELEROMETER SINGLE AXIS MEMS 2220 Series (Second)

Name: Testingindonesia
Rating: 5 (12 reviews)

Category: Alat Survey & Sensor Ready Stock Tags: jual sensor accelerometer second, jual sensor accelerometer single axis second, jual sensor getaran second Brand: SILICON DESIGN

Description

Dijual Sensor Accelerometer Single Axis Brand Silicon Design Series 2220, Kondisi Bekas/Second

Sensor Accelerometer Single Axis berfungsi untuk mengukur getaran, khususnya di suhu sangat panas/dingin

Spesifikasi:

• Low Noise: 10 µg√ Hz Typical for ±2g Full Scale Versions
• -55 to +125°C Operating Temperature Range
• Flexible +8 to +32 VDC Power
• Excellent Long-Term Stability
• ±4V Differential Output or 0.5V to 4.5V Single Ended Output
• Responds to Frequencies from Zero (DC) to 2000+ Hz
• Low Impedance Outputs Support up to 2000 Feet of Cable
• Integrated Cable or Connector, Traditional 1” & Small Footprint Sizes
• Simple Four (4) Wire Connection
• Rugged Anodized Aluminum Case
• Fully Calibrated and Serialized for Traceability

TERSEDIA: 6 UNIT

Harga 6 Unit : Rp. 86.000.000

Harga 1 Unit: Rp.22.000.000

Informasi Lebih Lanjut, Dapat Hubungi Rizki

ZERO TO MEDIUM FREQUENCY APPLICATIONS

SDI Accelerometer apps

g Range	Sensitivity, Differential	Frequency Response (Typ, 3 dB)	Frequency Response (Min, 3 dB)	Frequency Response (Typ, 5%)	Output Noise, Differential (RMS, Typ)	Max. Mechanical Shock (0.1 ms)
g	mV/g	Hz	Hz	Hz	μg/(root Hz)	g (peak)
±2	2000	0 – 525	0 – 300	0 – 250	10	2000
±5	800	0 – 800	0 – 420	0 – 400	15	2000
±10	400	0 – 1100	0 – 660	0 – 700	23	5000
±25	160	0 – 1750	0 – 1050	0 – 1300	38	5000
±50	80	0 – 2100	0 – 1400	0 – 1600	60	5000
±100	40	0 – 3000	0 – 1700	0 – 1700	121	5000
±200	20	0 – 3600	0 – 2100	0 – 1900	243	5000
±400	10	0 – 4200	0 – 2400	0 – 2000	475	5000

OPERATION

SDI Models 2220 and 2276 MEMS DC Accelerometers provide optimal performance when they are connected to instrumentation in a differential configuration using both the AOP and AON output signals, but they also support single ended operation for complete flexibility.

These Accelerometers produce differential analog output voltage pairs (AON & AOP) which vary with acceleration. The signal outputs are fully differential about a common mode voltage of approximately 2.5 volts. At zero acceleration, the output differential voltage is nominally 0 volts DC; at ±full scale acceleration, the output is ±4 volts DC, respectively, as shown in the figure (below). The output scale factor is independent from the supply voltage of +8 to +32 volts.

When a differential connection is not possible, SDI recommends connecting the accelerometer to instrumentation in single ended mode by connecting AOP and GND to the instrumentation and leaving AON disconnected. Keep in mind that the signal to noise ratio is reduced by half for a single-ended vs. a differential connection.

PERFORMANCE - ALL VERSIONS

All Models: Unless otherwise specified, Vs=+8 to +32 VDC, TC=25°C, Differential Mode. Span = ±g range = 8000 mV.

PARAMETER	MIN	TYP	MAX	UNITS
Bias Calibration Error (%)		0.25	0.6	± % of span
Bias Calibration Error (mV)		25	60	± mV
Scale Factor Calibration Error (1)		0.5	1.25	± %
Non-Linearity (-90 to +90% of span) (1)		0.15	0.5	± % of span
Bias Temperature Shift (Coefficient)	-100	0	+100	(PPM of span)/°C
Scale Factor Temperature Shift (Coefficient)	-150	0	+50	PPM/°C
Cross Axis Sensitivity		2	3	± %
Power Supply Rejection Ratio	50	>65		dB
Output Impedance		1		Ω
Output Common Mode Voltage		2.5		VDC
Operating Voltage	8		32	VDC
Operating Current (AOP & AON open)		7	10.5	mA DC
Operating Temperature	-55		+125	°C
Mass 2220 / 2276 (not including cable)		10 / 9		grams
Cable Mass (10’ integrated cable, 2220)		4.25		grams/foot

Note (1): For 2g thru 50g only; 100g and greater versions are tested and specified from -65 to +65g.

NOTICE: Stresses greater than those listed may cause permanent damage to the device. These are maximum stress ratings only. Functional operation of the device at or above these conditions is not implied.